The content below on the subject of Installing A Bathtub is especially enlightening. Read it yourself and decide what you think of it.
Mounting a bath tub isn't precisely rocket science, but it does need solid plumbing, woodworking, and also occasionally, tiling abilities. Changing an old bath tub with a brand-new one is also a moderately hard task. If the old tub is readily easily accessible, the project can move easily; if you have to open a wall to get rid of the old tub and position the brand-new bath tub, the job is a lot harder. In either situation, the project is within a residence handyman's skills, although you will need an assistant to vacate the old bathtub and also embeded in the new one. Make sure you have actually qualified on your own for the job and are comfortable trying it. Instead of hiring a contractor to take over a halfway-completed project, it is better to take into consideration utilizing one prior to you start. Possibilities are you might require a specialist plumber to make tube connections.
This article will certainly help you mount a new bath tub in your washroom if you have actually already gotten a new tub and also do not require to transform the setup of your previous supply of water pipes.
Your tools and product list must make up the following:
Preparing for the Setup
To start with, the supporting frame provided with the bath ought to be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is necessary to see to it that if the tap comes with a plastic washer, it is fitted in between the bath and also the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the adaptable tap connectors to the bottom of both taps making use of 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet with the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you make use of all of the provided washers.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath should currently be ready to be suited its final setting.
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installment, then the first thing you ought to do is detach the supply of water. After doing so, activate the taps to drain pipes any water continuing to be in the system. The process of removing the existing taps can be quite bothersome as a result of the limited access that is usually the situation.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the taps. Have a cloth all set for the remaining water that will come from the pipelines. When the supply pipelines have been removed, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the single taps from transforming during this process. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Prior to carrying on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the brand-new taps to fit.
Setting up the Tub
Utilizing both wooden boards under its feet, place the bathtub in the called for placement. The wooden boards are valuable in uniformly spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 small points.
The following goal is to guarantee that the tub is leveled all round. This can be achieved by checking the spirit level and also adjusting the feet on the bathtub until the spirit level reads level.
To mount faucets, fit the bottom of the furthest adaptable faucet connector to the ideal supply pipe by making a compression sign up with; then do the exact same for the other faucet.
Activate the water system as well as check all joints and brand-new pipework for leakages and also tighten them if required. Load the tub and also check the overflow electrical outlet as well as the typical outlet for leakages.
Ultimately, deal with the bath paneling as described in the manufacturer's user's manual. Tiling and sealing around the tub ought to wait till the bath tub has been used a minimum of when as this will certainly settle it right into its final setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end provides a link to the existent supply pipes.
If you need to fit a monobloc, after that you will require minimizing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin making sure that the washing machines remain in area between the tap and also the sink. Protect the faucet in place with the producer given backnut. As soon as the tap is safely in position, the supply pipelines can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical tap adapters. The former kind should be connected to the faucet ends initially, tightening up only by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath satisfies the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to crack a rigid seal, causing the water to permeate the wall between the bathroom as well as the tiling, bring about complications with dampness and also feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your fixtures as well as fittings. They are marketed in tubes and cartridges, and can sealing spaces up to a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of soaked newspaper or soft rope. Remember to constantly load the bathtub with water prior to sealing, to permit the movement experienced when the tub is in usage. The sealant can fracture rather very early if you do not take into account this activity before sealing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally conveniently available on the marketplace. It is advisable to fit the tiles making use of water-resistant or water-proof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I have been very eager about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I really hope you appreciated our blog post. Are you aware of someone else who is excited about the niche? Feel free to share it. I love reading our article about A Step-by-Step Guide to Installing a Bathtub.
For quick relief, contact!